AXION 850/820.

Packed with power.

1. With an output of 197 to 238 PS (to ECE R 120)
2. GPS PILOT automatic steering system
3. HEXASHIFT transmission
4. Prepared for ISOBUS
5. Long wheelbase for driving comfort and ideal weight distribution
6. Favourable 33 kg/hp (45 kg/kW) weight-to-power ratio and high load capacity
7. Reduced engine speed at maximum ground speed of 40 km/h / 50 km/h
8. Mechanical 4-point cab suspension
9. Factory-fitted wheel weight
10. Up to six spool valves, two of which are electronically controlled with time and flow control

Turbocharger with variable geometry (VGT).For high torque, even at low engine speeds, the turbine blades are adjusted depending on speed and load. This means no more 'turbo lag'.

CLAAS POWER MANAGEMENT (CPM).All AXION 800 models are fitted with the innovative CPM. Depending on the tractive power requirement, PTO output or hydraulic power decrease, up to 35 hp additional engine output will be gradually released under the following conditions:

• Transmission in range C or D (C1 = 6 km/h)
• If hydraulic output is decreasing
• If PTO output is decreasing

The CPM releases the additional boost power in six stages, so it never releases more fuel-hungry power than is actually required.

It supports you with the best high technology. Thanks to HEXASHIFT and the DRIVESTICK, you can shift effortlessly through all six powershift speeds and the four ranges using your fingertips, or shift automatically using the HEXACTIV powershift unit.

HEXASHIFT 6-speed powershift module electrohydraulically activated 4-range range shift REVERSHIFT hydraulic reverser optional creep gears

CLAAS HEXASHIFT offers clear benefits.

• No need to use the clutch when changing range
• Good gear spacing in the main operating range
• Fully automatic shifting with HEXACTIV
• Excellent efficiency in the field and on the road for low fuel consumption
• Creep gear option down to 400 m/h
• Convenient adjustment options with CIS
• High operating comfort with the DRIVESTICK
• Powertrain management for smooth changes in range and powershift operations

The right ground speed at all times.Whether you choose the 40 km/h or the 50 km/h transmission model, the gear spacing in the lower ranges A to C remains the same. This means that you will always have enough ratios available in the main operating range during field work.

Make your road travel and maintenance operations more economical:

• 50 km/h max. speed as an option (not available in every country)
• High transmission efficiency
• Low fuel consumption, even with partial loads
• High ride comfort
• Reduced engine speed at 40 km/h and 50 km/h with HEXASHIFT

Short overall length for:

• good manoeuvrability
• short trailer combination on the road
• good visibility
• good guidance of front-mounted implements

Long wheelbase for:

• high level of driving comfort
• directional stability
• higher tractive power
• good and secure road holding
• higher lifting power

Wide range of applications. Up to 35 hp usable boost power:

• Wide range of applications. Up to 35 hp usable boost power:
• From 6.0 km/h during tillage
• During drilling – heavy PTO work
• During trailer and transport jobs
• During baling

A low power-to-weight ratio:

• For low fuel consumption during light work
• For low ground pressure during field maintenance
• For dynamic road transport
• For greater flexibility: the power-to-weight ratio can be increased through ballasting if higher traction is required.
• For a high load capacity
• Weight distribution with front ballasting: front / rear 50% / 50%

Make use of the tractive power built into the AXION 800:

• Rear axle tyres up to 2.05 m in diameter
• Up to 400 kg wheel weights per rear wheel
• Flanged axle or 2.5 and 3 m adjustable axle
• Configured for dual wheels at the factory (dual wheels on front axle only available with AXION 850)
• High chassis efficiency with careful matching of transmission and rear axle
• Good weight distribution and a long wheelbase
• Factory-fitted front ballast up to 900 kg

A tractor can never apply a tractive force in excess of its weight. However, ballasting enables the AXION 800 to perform even better during traction work.

The control concept for the rear hydraulics with 10 t maximum lift capacity was designed specifically for the AXION 800 with a strong focus on practicality:

• Draught control
• Position control
• Wheel slip control
• Straightforward operation
• Automatic PTO engagement/disengagement

A fully integrated front linkage. And it's factory-fitted.When developing the AXION 800, a fully integrated front linkage with up to 5.4 t lift capacity and a front PTO shaft were envisaged from the outset. Accordingly, this version is available ex factory, and offers many advantages when compared with more conventional retrofitting solutions.

Benefits of the integrated front linkage:

• Perfect transfer of force to the tractor
• High lift capacity Integrated front PTO
• Integrated hydraulic and electric connections
• Two lift capacity options (3.3 t and 5.4 t)
• No retrofitting required at the dealer
• Vibration damping

Extend your range of applications – AXION 800 and the CLAAS front loader:

• Quick attachment and removal without tools
• Fully integrated CLAAS mounting bracket
• A robust, effective combination
• SHOCK ELIMINATOR vibration damping for exceptional driving comfort

• 540/1000 rpm as standard
• 540/540 ECO + 1000 rpm optional
• Front PTO shaft (1000 rpm)
• Remote control switch for front and rear PTO shafts
• Automatic PTO control can be adjusted for lifting height of rear linkage
• Up to 35 hp boost for PTO work with CPM

AXION 800 – the hydraulics.

• Load-sensing hydraulics with 110 l/min flow or optional 150 l/min flow for applications with a high oil demand
• Up to four mechanical spool valves
• Power Beyond connections at the rear
• CPM provides up to 35 hp boost if hydraulic output falls

Numerous hitching options.

• Drawbar
• Pick-up hitch
• Standard clevis
• Automatic clevis, 38 mm and 32 mm
• Ball hitch drawbar
• Ball hitch in the hitch frame